Problems with Install Boot
- Thread starter Caldir
- Start date
-
Hello Guest. Before you post check the Troubleshooting guide here, Dortania Troubleshooting
the PCI Devices are correct ? Or have to Delete the 1st with acpi-path ?
maybe i need remap my USB again or something is wrong.
your APCI settings also replace with my settings.
patches_OC.plist into my info info.plist
By the way i still need the USBTool Kext + Mapping ?
Found out some kexts not loading anymore USBTool and UTB dont know whats happen right know.
Your config put into my config.plist and replace after snapshot.
the PCI
im on sequoia but it doesnt matter so much i guess
Last edited:
there is my USB Mapping in windows seems good
the 2 red beside the ethernet also dont work.
but the blue ports with usb work ... they are all on the same controller
This USB Mapping is so painful ^^
the 2 red beside the ethernet also dont work.
but the blue ports with usb work ... they are all on the same controller
This USB Mapping is so painful ^^
Attachments
I would make the following points:
Ports 11, 12 & 17 under the first USB Controller appear to be ‘Internal’ devices, either directly connected to the motherboard or via a USB header. So these ports should be set as ‘Internal’ with connector type (255). I am not positive about the two LianLi fans but the ITE device is definitely an internal device.
You don’t have a Bluetooth device showing, is that correct for your system?
Pay attention to the screen showing the Companion ports, as these are helpful when looking to correct and/or matching port types.
The two Red ports you can’t see may be attached to a USB 3.2 & 2.0 hub, which would mean they don’t show as individual ports. But the same port, such as port #5 & 10 under the first USB controller might keep being highlighted when a USB drive is inserted.
Ports 11, 12 & 17 under the first USB Controller appear to be ‘Internal’ devices, either directly connected to the motherboard or via a USB header. So these ports should be set as ‘Internal’ with connector type (255). I am not positive about the two LianLi fans but the ITE device is definitely an internal device.
You don’t have a Bluetooth device showing, is that correct for your system?
Pay attention to the screen showing the Companion ports, as these are helpful when looking to correct and/or matching port types.
The two Red ports you can’t see may be attached to a USB 3.2 & 2.0 hub, which would mean they don’t show as individual ports. But the same port, such as port #5 & 10 under the first USB controller might keep being highlighted when a USB drive is inserted.
i disabled LAN / WIFI / Bluetooth
USB front header also Internal ?
By the way i saw XH00 XHC1 so all rename to XSTA is that ok ?
USBTmap -> is all about XH00, XHC0, XHC1, XHC2 <- thats are my 4 controller...
should i change in UTBmap.kext ?
"Ports 11, 12 & 17 under the first USB Controller appear to be ‘Internal’ devices, either directly connected to the motherboard or via a USB header. So these ports should be set as ‘Internal’ with connector type (255). I am not positive about the two LianLi fans but the ITE device is definitely an internal device."
That i have fixed.
"The two Red ports you can’t see may be attached to a USB 3.2 & 2.0 hub, which would mean they don’t show as individual ports. But the same port, such as port #5 & 10 under the first USB controller might keep being highlighted when a USB drive is inserted."
I try, no reaction. Just 1 short light from the USB, nothing happens.
Red Ports Behind beside Ethenet, Blue Ports behind
the Blue Ports Behind work. Testet
USB front header also Internal ?
By the way i saw XH00 XHC1 so all rename to XSTA is that ok ?
USBTmap -> is all about XH00, XHC0, XHC1, XHC2 <- thats are my 4 controller...
should i change in UTBmap.kext ?
"Ports 11, 12 & 17 under the first USB Controller appear to be ‘Internal’ devices, either directly connected to the motherboard or via a USB header. So these ports should be set as ‘Internal’ with connector type (255). I am not positive about the two LianLi fans but the ITE device is definitely an internal device."
That i have fixed.
"The two Red ports you can’t see may be attached to a USB 3.2 & 2.0 hub, which would mean they don’t show as individual ports. But the same port, such as port #5 & 10 under the first USB controller might keep being highlighted when a USB drive is inserted."
I try, no reaction. Just 1 short light from the USB, nothing happens.
Red Ports Behind beside Ethenet, Blue Ports behind
the Blue Ports Behind work. Testet
Last edited:
