Search results

Here is the result: The IOPCIIsHotplugPort patch should work in Tahoe Beta 1 as explained in the screenshot below. Tahoe is on the left, Sonoma is on the right.

Working on it now...

Sure; once the KDK for Beta 2 is released I’ll check the patch.

SOLVED: It turns out that Tahoe Developer Preview #2 encounters the freeze at about 16 minutes remaining. But Developer Preview #1 works! Just got Tahoe DP1 installed on Asus X670E Gene, and will perform an in-place upgrade to DP2.

Additional comments: On my Asus X670E Gene, BIOS was upgraded to 3104 With help from @fabiosun and CorpGhost, new ACPI (DSDT) patches were created overnight, and they work perfectly USB port mapping was done using CorpNewt’s latest USBMap package I can fully boot Sequoia using the new EFI...

This issue is confounding me at the moment. My experience so far with Tahoe installation: Intel systems: Asus Z690 ProArt -- success Asus Z690i ROG Strix mini-ITX -- success Gigabyte Z390 Designare -- success Gigabyte Z490 Vision D -- Freeze at about 16 minutes remaining AMD systems...

I just started the process of installing Tahoe Beta on my Gigabyte B550 Vision D: Tahoe installer boots up properly (and fairly quickly) Tahoe installation process starts with "20 minutes remaining" At about 16 minutes remaining the process freezes and a spinning beachball appears after a few...

@JohnFante Apologies for the very late reply. If this is still an issue, my first question is whether DSDT patches are needed for the Gigabyte X670E, particularly with recent BIOS updates. If so, have you applied any DSDT patches?

The DisplayPort connection from my Z390 Designare to a 4K mini-LED monitor also blanks out every once in a while for about 3-5 seconds, but there’s a KVM switch between the computer and monitor. I don’t experience these black outs on two other systems connected via the same KVM. The Designare...

Does your X670e Hero have an AS Media USB4 controller or an Intel Maple Ridge?

@errevi, For the XH00 device located here _SB.PCI0.GPP7.UP00.DP40.UP00.DP60.XH00, there is no RHUB child device in DSDT. This is most likely why USBToolBox is unable to map USB ports. Also notice this:

@fabiosun, Does this mean that the 3 ACPI patches provided by CorpNewt will allow macOS to boot on any of the new BIOS versions? 2204 and 2308 and others? Or are these ACPI patches specific to a particular motherboard model? Are they for Asus motherboards only?

Hello @Tormod, It’s been a busy week at the office so I’ll take a look at your EFI folder this weekend. Thunderbolt hot plug is very elusive with Maple Ridge on an AMD system. Making things worse is my observation that any attempt to change Thunderbolt device properties results in even more...

@Edhawk, You're quite right; the Orange Pi Wi-Fi 6 card is Key M that is meant for standard M.2 PCIe slots. Typical Wi-Fi models are either Key E or Key A/E. Key M provides access to 4 PCIe lanes, but Keys A and E provides access to 2 lanes of PCIe, plus UART and USB buses for Bluetooth. The...

Heliport and itlwm work, as reported by @Lorys89 here, but the developer himself apparently has very little time to work on this. I have ordered a Broadcom WiFi 6 module from AliExpress, but I don't know if it will work. It's cheap enough to experiment with, and because I have an OrangePi 5...

I decided to jump in as well. Applied latest beta AMD-OSX kernel patches from here Applied latest pre-release Acidanthera kexts from here Applied latest AMDRyzenCPUPowerManagement kexts from here Did not need to use -lilubetaall because latest (pre-release) Acidanthera kexts support Sequoia...

@tuort Awesome!! Yes I think the other SSDTs may also work, but there could be subtle differences between different device IDs.

Ethernet drivers in macOS require AppleVTD to be enabled. Looking at the IOReg files that you posted earlier, I can see that AppleVTD is not enabled. To enable it, please do the following: In BIOS, confirm that Intel VT-D is enabled In config.plist -> Kernel, confirm that DisableIOMapper is...

@tuort, Please disable the previous SSDT and try the attached version that uses Device ID 0x94C0, which is what I'm using on my Asus Z690 ProArt Creator.

@Danish297 Can you confirm that Ethernet connection over your 10GbE port works — you can actually connect to the Internet after disabling all other network devices in the Network Settings panel?