Can't install tahoe, hope someone can help

tr4c3r2k12

New member
AMD OS X Member
Mar 21, 2025
8
1
3
44
CPU:
Ryzen 7 9700x
hi, its been a while since my last post on this site, hope everybody is doing well, this is my problem, i have been using hackintosh since 10.4 to 15, everything went well, since january, i change to Linux, now im trying to install tahoe on another disk, i want to keep my Linux install, im trying to boot from the usb but it hangs, i dont know what could be the problem, this is my hardware MSI X870 Tomahawk WIFI - AMD Ryzen 7 9700x - DDR5 64 Gb 6000 Mhz G.SKILL Trident Z5 (32 Gb x 2) - 2 TB Kingston NV2, 256 Gb Kioxia MacOs - ASRock Radeon rx 6600 8 Gb, i have a Realtek RTL8126, use @laobamac_yyds SIMPLEAERL v1.1 kernel patches, but i dont know whats happening, i dont know if it could be related to usb mapping, is there a way to map USB ports in Linux?, and also, i dont know if i have all the SSDTs i need, ryzen is still kind of new to me i have always used intel, if someone could give me hand i really apreciated
 

Attachments

  • EFI.zip
    EFI.zip
    1.8 MB · Views: 2
  • IMG_9394.jpg
    IMG_9394.jpg
    301.6 KB · Views: 3
If anything, you have too many SSDTs: Keep only one of -CPUR and -PLUG-ALT, they serve the same function.
You alse have many disabled entries, which does not help reading the config.plist. And yet your DSDT may need some more patches to enable devices (see which ones, or post your ACPI tables).

Have you booted Sequoia, or earlier, on this system? Tahoe is more complicated, and installation may require trimming down the EFI (no unecessary kexts such as the AMD management ones).

Kernel panic has AppleRTL in backtrace, so I'd suggest to disable SimpleRTL patches and try with RTL812xLucy.kext instead.
 
  • Like
Reactions: Edhawk
hi, its been a while since my last post on this site, hope everybody is doing well, this is my problem, i have been using hackintosh since 10.4 to 15, everything went well, since january, i change to Linux, now im trying to install tahoe on another disk, i want to keep my Linux install, im trying to boot from the usb but it hangs, i dont know what could be the problem, this is my hardware MSI X870 Tomahawk WIFI - AMD Ryzen 7 9700x - DDR5 64 Gb 6000 Mhz G.SKILL Trident Z5 (32 Gb x 2) - 2 TB Kingston NV2, 256 Gb Kioxia MacOs - ASRock Radeon rx 6600 8 Gb, i have a Realtek RTL8126, use @laobamac_yyds SIMPLEAERL v1.1 kernel patches, but i dont know whats happening, i dont know if it could be related to usb mapping, is there a way to map USB ports in Linux?, and also, i dont know if i have all the SSDTs i need, ryzen is still kind of new to me i have always used intel, if someone could give me hand i really apreciated
Good tips from @etorix . Attached is an EFI I was using with an MSI X870E Carbon Wifi board attempting to use SimpleBCM.kext. You should probably note the kext section of the EFI contains multiple kexts that are not enabled including USB Port mapping kexts. Its very likely you can boot Tahoe without USB Port mapping, you'd need to find one of the ports that gets activated by Tahoe to be able to finish the install. If the prohibited sign shows its face try another port. Once you complete the install you can use Hackintool or CorpNewts USBMaster to zone in on identifying an accurate port map.
I don't have @laobamac_yyds SIMPLEAERL solution for the realtek RTL8126 but you can add it in. Maybe this will help get you off the ground.

In case it’s not immediately obvious you will need to adjust your CPU core counts.
 

Attachments

Last edited:
  • Like
Reactions: etorix and Edhawk
Its very likely you can boot Tahoe without USB Port mapping
Extremely likely, though can't confirm with the OPs hardware, and not to suggest you shouldn't.
 
The Verbose text image provided by the OP shows an issue with the Ethernet setup. So going with a standard Realtek Ethernet kext would be recommended.
 
  • Like
Reactions: leesurone
If anything, you have too many SSDTs: Keep only one of -CPUR and -PLUG-ALT, they serve the same function.
You alse have many disabled entries, which does not help reading the config.plist. And yet your DSDT may need some more patches to enable devices (see which ones, or post your ACPI tables).

Have you booted Sequoia, or earlier, on this system? Tahoe is more complicated, and installation may require trimming down the EFI (no unecessary kexts such as the AMD management ones).

Kernel panic has AppleRTL in backtrace, so I'd suggest to disable SimpleRTL patches and try with RTL812xLucy.kext instead.
hi @etorix i used to have sequoia in this machine, i havent change anything, i did upgrade the bios to version 1.A93, the SSDTs, CPUR and PLUG-ALT, both are on the folder but only CPUR is enabled, with PLUG-ALT the machine freezes, i attach the acpi tables from SSDTtime, thanks for your reply
 

Attachments

Good tips from @etorix . Attached is an EFI I was using with an MSI X870E Carbon Wifi board attempting to use SimpleBCM.kext. You should probably note the kext section of the EFI contains multiple kexts that are not enabled including USB Port mapping kexts. Its very likely you can boot Tahoe without USB Port mapping, you'd need to find one of the ports that gets activated by Tahoe to be able to finish the install. If the prohibited sign shows its face try another port. Once you complete the install you can use Hackintool or CorpNewts USBMaster to zone in on identifying an accurate port map.
I don't have @laobamac_yyds SIMPLEAERL solution for the realtek RTL8126 but you can add it in. Maybe this will help get you off the ground.

In case it’s not immediately obvious you will need to adjust your CPU core counts.
thanks @leesurone i will try it, and let you know what happends
 
The Verbose text image provided by the OP shows an issue with the Ethernet setup. So going with a standard Realtek Ethernet kext would be recommended.
i try without laobamac_yyds patches, and no kexts for network or wifi, the first efi y made only had lilu, virtualsmc and whatevergreen, restrictevents, and usbmap, cuald it be related to the usb ports not properly mapped, id there a way to map port on linux or is only for windows an mac? thanks for your reply @Edhawk, also what options in Bios should be enabled or disabled, i think i have them rigth but maybe i missed something.
 
✖
  AdBlock Detected
Sure, ad-blocking software does a great job at blocking ads, but it also blocks some useful and important features of our website. For the best possible site experience please take a moment to disable your AdBlocker.