Recent content by SchmockLord

Thanks. Yeah this is the same behaviour as I have in Sequioia, it doesn't go into sleep. Switching back to Sonoma with the same EFI fixed the problem. Only remaining issue I have left is, that it need two keystrokes to wake the display after sleep. But that is a minor cosmetic.

Can you try for me please? Just send him to sleep. And wake him up after couple of seconds sleeps. First with 1 keystroke. See if display comes up alone. And after 20-30sec hit the second key to see if display turns on then.

Hey, As you also have a B650 Board. Does your USBWakeFixup.kext work? So do you need one or two keypresses to wake the system up with display turning on? I always need two keypresses so the display turns on. And do you also have instant wakes after sleep on Windows/Mac?

@fabiosun I still have one issue left, and I had this on all my systems even though I changed my monitors a lot: It always takes me 2 keypresses to wake display. The system wakes after the first, but display needs the second. And also USB-sticks attached to the XH00 where also Keyboard&Mouse is...

Remove th It's probably because the SSDT-6950XT.aml is still active and tries to mock a 6950XT for your 6600. And installation works because in installation no GPU-acceleration is enabled.

Found an even better solution, which somehow didn't work before: Disabling XHC0-XHC2 via SSDT. It somehow didn't work when it was in the same SSDT as the XH00 USB-Port config, but now as a separate SSDT-Disable-XHC.aml it somehow works. So now everything works and I don't need a modified...

Ok I found another solution than just disabling the USB2 Ports in BIOS, because its also not nice to have no USB2 support on Windows. I have removed the XHC0-XHC2 definition from the DSDT.aml of the BIOS 3.03. And then injected the SSDT-11 which was the XHC0-XHC2 definition from the BIOS 1.30...

@fabiosun @tomnic I think I solved it. I could enable all USB3/USB3.1 Ports in BIOS and Shutdown works. But as soon as I enable the USB 2 Ports, shutdown ends in restart. Funny thing is, if I disable USB2 Ports in BIOS, they still work in macOS. Now I am on BIOS 3.03 with AGESA 1.2.02 and the...

@fabiosun He couldn't help me. My DSDT needed no patches. Attached my most current EFI. I even applied your ASUS patches, don't know if they are needed or not.

@fabiosun No I haven't. Can you send me the invite link to the server you mean? Would be very nice :)

@leesurone I am pretty sure it's something they messed up with the BIOS over time. As soon as I go back to v1.30 A05 shutdown works again, no matter if it is with the SSDT or Kext based USB Mapping. So I will just stick to 1.30 A05 now. I thought about trying with v3.03 but injecting the...

So @leesurone I am back home and tried to apply your recommendations. I have the config as SSDT and Kext. I noticed, that when I use the SSDT, on the second boot there come duplicates of e.g. POT1 and POT3. This is after the first boot with the SSDT: Looks totally ok to me. All utilized...

Thanks. Will try that again. Have done something in the past 24h but I am at work, so the EFI is not my most current one. At home I already have made a map of my board and wrote down all port names to each physical port. And I have also noticed that ports that are defined by ASROCK as USB2 are...

I have an ASRock B650M Pro RS Wifi with BIOS 3.08 and AGESA 1.2.02 and have the issue, that the PC Restarts instead of Shutdown. PC shuts down for a second and then immediately turns on again. But it's not defaulting BIOS settings, so it's not a safe-mode restart. But sleep works fine. I tried...

Do you know any AM5 board where TB Hotplug works over a shutdown/restart? Mini-ITX/Micro-Atx preferred.