x570 hackintosh cannot boot after updating BIOS

[tung_opeth]

i just upgrade my bios, and it turns out like this, any idea?
crosshair 8 wifi latest bios (ROG CROSSHAIR VIII HERO(WI-FI) BIOS 2103)
ryzen 5 3600
now i cannot do anything to change the config

i follow dortania's troubleshooting yet still no luck (https://dortania.github.io/OpenCore...vqWT2UKu7uR_rqichpg#stuck-on-eblogexitbsstart)

Thanks for reading!

 

[Aluveitie]

Check this thread: Asus BIOS Upgrade - Stuck [EB|#LOG:EXITBS:START]

 

[GuessWhosBack]

I had the same problem. I think I fixed it setting SetupVirtualMap to false and RebuildAppleMemoryMap to true. Just follow the instructions for trouble shooting: https://dortania.github.io/OpenCore-Desktop-Guide/troubleshooting/troubleshooting.html

 

[olbo]

Updating your BIOS also usually resets your configuration - so check that again.

Zen · GitBook

dortania.github.io

 

[tung_opeth]

thanks guys, i solve the problem messing around with booter's quirks config as you guys mentioned above

 

[KirillMarkov]

Hi guys!
I have the same problem with ROG Crosshair VIII Hero motherboard. My ryzentosh stuck on EXITBS:START since bios version 2010.

I set quirks as:
SyncRuntimePermissions = True
RebuildAppleMemoryMap = True
SetupVirtualMap = False

Before my settings was:
SyncRuntimePermissions = False
RebuildAppleMemoryMap = False
SetupVirtualMap = True

My system also can’t boot with any bios version since 2010 up to 3xxx, but it works well with any of 1xxx bios version.

I tried any combinations of these quirks, but there’s no result.

Have you any ideas?

Best regards,
Kirill

 

[KirillMarkov]

Update:
My system still can’t boot with new bios.
If I enable “above 4G decoding” option and remove “npci=0x2000” from boot args, boot stuck at “PCI configuration begin”.
If I disable “above 4G decoding” and add “npci=0x2000”, I have the same error.
If I enable “above 4G decoding” and add “npci=0x2000”, my system start booting, but it always reset after following log strings:
IOConsoleUsers: gIOScreenLockState 3, hs 0, bs 0, now 0, sm 0x0
apfs_load_inode_internal:6107: *** reset ino 12944875 size block to 37993 (from 64324)

 

[Aluveitie]

Make sure ResizableBAR is disabled if that option is present. If you disable Above 4G decoding you could try npci=0x3000.
Also re-check all relevant BIOS settings, after update everything is reset to default.

 

[KirillMarkov]

ResizableBAR is disabled. I also tried npci=0x3000, result was the same. After update bios I always clear CMOS and resetup.

 

[KirillMarkov]

Here is my EFI

 

[Aluveitie]

@KirillMarkov Remove the DSDT.aml from your EFI/config.plist. You should not need to have it there, and it can break on every BIOS update or even BIOS reconfiguration

 

[KirillMarkov]

Thank you, system can boot now, but it always stuck after ~1 min with error

 

[Aluveitie]

Make sure you have the DummyPowerManagement Quirk enabled

 

[KirillMarkov]

Thank you, this quirk was disabled

 

[KirillMarkov]

Also now sleep is not working.
On last configuration sleep mode worked.

 

[Aluveitie]

If you’re on Catalina you could try Big Sur, that fixed a lot of issues.
Otherwise you could backtrack your changes to the DSDT and rewrite them as proper SSDT patches so it does not break on every BIOS update.

 

[KirillMarkov]

I’m on Big Sur. On Catalina sleep worked only without Bluetooth card.